   |
|
Dataprobe iBootBar
Remote Reboot - Power Control - Energy Management - Power Distribution
Beschreibung
Get all the power of the iBoot and more with these remote reboot power strips. Control each outlet independently from Web, Telnet, SNMP. Have network access plus out-of-band control via serial port and internal modem with both data and DTMF tone dial control. Wherever you are, you are in complete control.
iBootBar is available with single or dual power inlets. Dual power is ideal for remote reboot control servers, routers, etc. with redundant power supplies. Simultaneously switch both supplies off and on for reboot, security or energy management. These models are also ideal for switching higher current devices. Each inlet is distributed to 4 outlets, which can be switched in pairs for redundant systems, or individually for higher current devices.
Models are available for North American 15 and 20 amp circuits, as well as international 115/230 VAC, up to 20 amps.
The internal modem option allows connection to the iBootBar from anywhere, anytime. Dial-in with a laptop or terminal for complete control of all functions, or access iBootBar with any telephone for quick power on, off or reboot functions. Telephone users are guided with voice prompts and status information.
iBootBar continuously monitors the current draw from its outlets and reports user settable high and low current alarms. Know immediately when there is too much load, or a device stops working. Alarms are delivered both by email and SNMP traps.
Link up to 16 iBootBars together and control 128 outlets from a single IP address and Web page. Groups and User rights across multiple iBootBars allow power management across your entire network.
- Web and DTMF Tone Control in the same unit!
- Multi-Outlet, Multi-User Remote Reboot
- Outlet Grouping for Simultaneous Switching
- Current Sensing and Alarming
- Expandable to 128 Outlets
- AutoPing for Automatic Failure Detect and Reboot
- SNMP Manageability
- Full Compliance - UL - CE - FCC
Bedienung
| Simple Web Browser Power Control The web browser interface provides the easiest means of managing multiple outlets. One master unit can be connected to 15 expansion units, managing 128 outlets from a single web page interface. The web page presents a clear status indication of each outlet, current draw across all inputs and the AutoPing monitoring, if implemented. Each outlet can be individually selected, or multiple outlets can be simultaneously operated. User selectable cycle timer allows single command reboot. Delay timer limits inrush current by staggering power up when multiple devices are simultaneously controlled. |
Simple Web Page Control |
| Multiple Users / Multiple Rights Up to 15 users can be identified, each with specific rights to one or more outlets, as well as administrator rights for programming the system. User rights can span multiple units, so that one user can command a specific outlet in each of several data cabinets. Users only see the outlets they have rights to. User rights function the same for both web browser control and the Telnet or serial command line interface. |
Multi User Setup |
| Group Outlets Two or more outlets can be grouped together for simultaneous action. Link all email servers together to reboot the entire system, or group both power feeds for dual redundant servers, and reboot the server with one command. Like outlets, groups are individually named and assigned to users as required. Group outlets across multiple iBootBars to simultaneously manage like devices across cabinets throughtou your data center. |
Outlet Group Control |
| Control 128 Outlets from Link 16 iBootBars together with the Expansion Port and manage 128 outlets from as ingle IP Address and Web Page. Group outlets accross racks to reboot multiple outlet simultaneously. Assign users rights to similar devices throughout the data center. Use the expansion to conserve IP addresses, or connect each device to the network for additional access capabilities. |
|
| Manage Multiple iBootBars The iBootBar Setup and Control Utility allows simple management of an unlimited number of iBootBars in the field. All configuration parameters can be set, saved, cloned, uploaded and downloaded to or from any iBootBar. This makes it easy to make configuration changes to similar units, or to pre-configure many units prior to deployment. The Setup and Control Utility also provides secure power management for all outlets deployed worldwide. |
Setup and Control Utility |
Eigenschaften
| Access from any Network point or any Telephone | No field trips required for Reboot. Save time and money by eliminating service calls and reducing downtime to a minimum. | ||||||||||
| Multiple Control Options |
| ||||||||||
| Multi-User | Assign permissions to each user for outlets and configuration. Users see only outlets assigned | ||||||||||
| IP Addressed, 10/100Base-T | Use on any Ethernet IP network. Public or private. Supports DHCP and alternate ports for Web Access. | ||||||||||
| Automatic Reboot Operation | AutoPing Automatic Operation for crashed devices. AutoPing pings device and takes action when no response. Complete control over frequency and timers. | ||||||||||
| Current Sensing and Alarms | Know when critical power conditions occur and take immediate action. Email and SNMP Trap notification. | ||||||||||
| North American and International Versions | 115 VAC with N. American cords and plugs. 100-240VAC with IEC connections | ||||||||||
| Dual and Single Power Inlet | Supports dual redundant powered devices with a single click. | ||||||||||
| Group and Stagger | Combine any outlets into logical groups and power up devices in sequence to reduce power surges. | ||||||||||
| Manage 128 Outlets | One IP address and Web Page for up to 128 outlets. | ||||||||||
| Setup and Control Utility | Save, Clone, Manage multiple configurations. Makes deployment of similar units a snap. | ||||||||||
| SSL Certificate Utility | Create and deploy SSL Certificates. Self Signed or Root Authority Certificates | ||||||||||
| Direct TCP Messaging | Integrate iBootBar into your OEM application with direct TCP messaging protocol. Compatibility Mode for original iBB-N15 series products. (requires firmware update to iBootBar Precision. See Resource Tab) |
Spezifikationen
| PHYSICAL: |
| ||||||||||||||||
| A/C INPUT |
| ||||||||||||||||
| NETWORK | 10/100 Ethernet Web, Telnet, SNMP, SMTP Port Assignable for Web and Telnet. SSL Security on Web control | ||||||||||||||||
| SERIAL PORT | D9 Serial, configured as DCE. to 115.2Kbps | ||||||||||||||||
| INTERNAL MODEM | 56Kbps V.92 Global Compliance, Data or Tone Dial (DTMF) control | ||||||||||||||||
| SWITCHED OUTLETS |
| ||||||||||||||||
| COMPLIANCE |
|